Index to site

 


HOME                      

PRODUCTS & PRICES                 1)Engine Blocks
Cylinder Heads
Cam Tray/Lifter Valves and Springs Throttle Bodies    2)Pulley/Idler/Belt  3Jackshaft/Camshaft Flywheel  Gaskets  4)Studs Hardware Oil Pumps Water Pumps Cam Covers Manifold

PRODUCT SLIDE SHOW

ORDERING

TECHNICAL NOTES

PRODUCTS  page 2 of 4        Office 818 957 7477   Cell 310 880 0155   Tel/Fax 818 957 7477
Double Click on  for larger image or go to PRODUCT SLIDE SHOW

Parts Description

For more Technical Details refer to TECHNICAL NOTES

  Sale Price Weight lbs
 H.T.D. High Torque Drive, Complete Drive Pulley assembly (round not square tooth profile). Reduces power loss through belts and considerably more accurate timing and reliability against tooth jump on over rev. Recommended for use with high volume BDT water pump $809 5.4
  Adjustable Top Idler complete with bearing, circlip location boss, and offset adjuster. (Stud, washer and nut not included)   $168 1.2
  Top idler Stud, alloy packing washer and 12 point nut, set.   $19 0.2
  Two sizes of Top Idler available. Standard 75mm (2.95 ins) or larger 87mm    (3.425 ins) diameter. Please specify which you need      
  Bottom Idler fixed complete with bearing, circlip, locating boss and fixing  guide   $119 1.2
  Lightweight Camshaft Pulleys (set of two) complete with mounting plate, index dowel and tapered camshaft hub/pulley mounting boss (round tooth profile)   $290 3.1
 Lightweight Camshaft Pulleys (set of two) complete with mounting plate, index dowel and tapered camshaft hub/pulley mounting boss (square tooth profile)   $310 3.1

No Photo

  Original style Camshaft Pulleys Cast  Square tooth profile (each)   $145 1.2
 

  Jackshaft Pulley lightweight alloy, three bolt (round tooth profile)

  $125 0.8
  Original Style Jackshaft Pulley 'Original' Square tooth profile (on right)   $125 0.8
  Close-Up of round and square tooth pulley and belt profile. Both tooth profiles are on the same center to center. Clearly the HTD profile is vastly superior on drive belt/pulley engagement , the obvious consequence is greater  reliability at high RPM on high torque motors.      
 Water pump light alloy pulley with HTD round tooth profile belt 2.8in Diam Note this is slightly larger than standard  2.575 square tooth Cosworth pulley. 2.8in  Square tooth profile available by special order $128 $84 0.3

No Photo

  New lightweight Water pump pulley Standard square profile tooth belt design 2.575in Diam.   $74 0.3
  Crankshaft pulley heavy duty casting (square tooth profile)   $79 1.0
   Crankshaft pulley heavy duty casting (round tooth profile) $79 1.0
  "V" Belt profile pulleys, various sizes, mountings and spacers available, 2.7 inch and 3.2 inch diameters, enquire regarding hub details and mounting patterns.   $58each 0.3 each
  "V" Belt Pulley system 4 or 3 bolt pattern, 4 inch diameter kit( two pulleys and a belt suitable for alternator installation   $131 0.5 each
  "V" Belt 30 inch length, 0.835 ins or 21.2 mm wide   $24 0.3
   Original Square profile tooth belt, 1 inch wide 54.5 inches long   $42 0.5
   New HTD Round tooth profile belt, 24mm wide 54.5 inches long #5129   $38 0.5
   New HTD Round tooth profile belt, 1 inch wide 55.5 inches long #5040XS, 1 inch longer for larger idler   $40

0.5

PRODUCTS PAGE INDEX  (use pointer to jump to page)

Page 1: Blocks - Heads - Cam Tray - Followers - Valves - Springs - Throttle Bodies

Page 2: Pulleys - Belts - Idlers

Page 3: Jackshafts - Camshafts - Flywheel - Spring Retainers - Stem seals - Gaskets

Page 4: Studs/Bolts - Manifolds - Cam Covers - Oil Pumps - Water Pumps - Hardware

Web sites      www.BlueSkyRacing.com       

BlueSkyRacing NEWS